Introduction Since its introduction in 1970, only one type of petrol engine has been fitted to the the Range Rover: the all-aluminium Rover V8 unit, bought from Buick by Rover in the 1960s. The 3.5 litre V8 was first used in Rover's P5 saloon and thereafter, in the P6 and SD1 saloons. Inevitably, due to its versatility, the Rover V8 also found its way into sports cars - such as MGs and TR7s - as well as more utilitarian vehicles: Police riot vans, ambulances and naturally, a whole variety of Land Rover products. Still in production today, the Rover V8 is currently being employed by the likes of TVR, Morgan, Marcos and, of course, Land Rover. The reasons for the engine's overwhelming success are obvious: it's simple, reliable, light and reasonably compact, and can be easily adapted to suit almost any purpose. Its versatility is unquestionable: it can be supercharged, turbocharged and run on LPG. Finally, parts are cheap and readily available. Over the years, the engine has grown in capacity from 3.5 to 3.9, then 4.2 and ultimately (for Range Rover at least) 4.6 litres. Some - notably TVR - have even stretched the capacity to 5.0 litres and beyond. Add the bewildering choice of compression ratios available (due to the changing demands of various world markets over three decades) and the result is a confusing range of parts from which to choose when contemplating engine work. In the following section, we have attempted to simplify the choice wherever possible, but at the same time provide a complete range of parts to cater for all models.

 

Replacement Full Engines We offer various capacities of replacement (exchange) full engine, including 3.5, 3.9, 4.6, 4.8 & 5.2 litre, depending on the power/torque output you require. Any one of these engines can be fitted as a replacement for your existing engine, provided any necessary modifications to the fuel system are carried out. The compression ratio of all replacement engines is 9.35:1 and all are suitable for unleaded fuel. In addition, most engines are available in two power levels: Standard or Performance, as described below.

 

Standard Full Engines Standard engines are the perfect choice for anyone looking to replace a worn-out engine. Suitable for carb or efi applications, manual or automatic transmissions and built to run on unleaded fuel as well as LPG. These engines are a straight swop, enabling the existing ancillaries and fuel system to be retained. 3.9 litre engines are a popular replacement for 3.5 (carb or efi). Alternatively, a standard 4.6 engine works very well in place of a high-mileage 3.9 or 4.2 efi (the ecu will require remapping to suit). Standard engines are available in 3.5, 3.9 & 4.6 litre versions.

 

Performance Full Engines Performance engines are built to the same high specifications as our Standard versions, but incorporate certain modifications to increase power and torque. Ideal for the driver who requires more performance from their vehicle, these engines feature a higher lift, longer duration camshaft, Vernier timing chain and improved cylinder heads fitted with larger valves. To gain maximum benefit from these engines, we recommend the fuel system, exhaust and air filter be uprated to suit. (For example, a 3.9 efi vehicle fitted with a Performance 4.8 engine, would also benefit from a remapped ecu, stainless steel sports exhaust and K&N air filter). Performance engines are available in 3.9, 4.6, 4.8 & 5.2 litre versions.

 

Engine Number Identification We have included a reference chart of Range Rover V8 engine numbers from 1970 onwards, which will help you to identify the engine fitted to your Range Rover. The engine number of most Range Rover V8s is stamped on the left hand side of the block deck, adjacent to the dipstick tube, although some very early models had the engine number stamped on the bellhousing flange at the rear of the block. The chart also contains a brief description of features, such as compression ratio and gearbox type, and also the approximate year fitted. Therefore, if your engine has been changed at some time, it should still be possible to correctly identify it. To ensure you receive the correct parts, please have your engine number ready before ordering. Note: "Pulsair" and "Air Injection" are terms applied to engines equipped with Air Rail type cylinder heads, ie cylinder heads with steel pipes located in holes just above the exhaust ports. (Fitted to carburettor engines only.) "Detoxed" refers to a variety of emission control devices, including Air Rails, fitted to carb engines.

Engine Numbers

V8 Engines - Standard

New 'long' engine;
New long engines are essentially a 'stripped' full engine (ie not as complete as a full engine). Comprising of new cross-bolted short engine fitted with new heads (less rocker gear and cam) they are obviously cheaper than the comparative 'full' engine. It is essential to ensure that the build-up of a 'long' engine is carried out properly, ensuring that all components such as rocker gear, cam/followers, timing gear, oil pump, timing cover, sump etc are checked/overhauled/replaced to validate our warranty. Suitable for carb or efi vehicles, please state model/year when ordering to ensure correct heads are fitted.
4.0 litre - (1) - ERR5012ST
4.6 litre - (1) - ERR5013ST

New full engine;
New full engines comprise; new short engine (new block/crankshaft/bearings/pistons/con rods) fitted with new camshaft and followers, new timing gear, new oil pump & oil pressure switch, new cylinder heads & rocker gear.
Suitable for carb or efi vehicles.
3.5 litre - (1) - RRV-227
3.9 litre - (1) - RRV-228
4.6 litre - (1) - RRV-229

Recon full engine;
Recon engines comprise; reconditioned block, rebored with new pistons, new cam bearings, reground crankshaft, new bearings, new camshaft & followers, new timing gear, new oil pump gears & pressure switch, recon cylinder heads with new valves, guides (inc latest type seals) & springs. New rocker shafts & rockers. Fitted with timing cover and sump.
Suitable for carb or efi vehicles.
3.5 litre - (1) - RRV-227R
3.9 litre - (1) - RRV-228R
4.6 litre - (1) - RRV-229R

NOTE: Full Engine units (which are supplied less water pump and other ancillaries) are usually sold on an exchange basis (Recon) or outright (New). Please refer to Price Guide. The old unit must be a suitable type (ie Range Rover or Rover SD1) otherwise a surcharge will apply.
All full engines, including 4.6 units, are suitable as direct replacements for any Range Rover V8 engine. Existing ancillaries can be re-used and all threads and fixings are compatible. Note that modifications to the fuel system may be required if replacing a 3.5, 3.9 or 4.2 engine.
Note: All standard engines are bench run and are compatible with unleaded fuel and L.P.G.
For manual transmission vehicles, we recommend fitting a new clutch while the engine is being replaced.

Engine installation kit - (1) - RRV-236
Includes running-in oil, oil filter, gaskets etc.

V8 Full Engines - Performance

---

Performance engines are available in 3.9, 4.6, 4.8 & 5.2 litre capacities. They are built to the same high specifications as our Standard versions, but incorporate certain modifications to increase power and torque. Ideal for the driver who requires a little (or a lot!) more from their vehicle, these engines are available in a choice of power outputs to suit any requirement and any budget.

Performance full engine - V8;
Fitted with performance cam and big valve cylinder heads.
Compression ratio is 9.35:1. Suitable for carb or efi vehicles.
3.9 litre - (1) - RRV-230R
4.6 litre - (1) - RRV-231R
4.8 litre - (1) - RRV-232R
5.2 litre - (1) - RRV-339

NOTE: Full Performance Engines (which are supplied less water pump and other ancillaries) are usually sold on an exchange basis (Recon) or outright (New). Please refer to Price Guide. The old unit must be a suitable type (ie Range Rover or Rover SD1) otherwise a surcharge will apply.
All full engines, including 5.2 units, are suitable as direct replacements for any Range Rover V8 engine. Existing ancillaries can be re-used and all threads and fixings are compatible. Note that modifications to the fuel system may be required if replacing a 3.5, 3.9 or 4.2 engine.
Note: All performance engines are bench run and supplied with a dyno (power output) sheet.
For manual transmission vehicles, we recommend fitting a new clutch while the engine is being replaced.

Engine installation kit - (1) - RRV-236
Includes oil filter, gaskets etc.

 

Specification We start with a strengthened bottom end, carefully balanced to ensure smooth, vibration-free running. 3.9 litre engines are based on a reconditioned, late-type block, which is rebored and fitted with new 94mm cylinder liners. (Note: we sometimes use brand new 3.9 short engines, depending upon price & availability). The crankshaft is reground and micro-polished, fitted with heavy duty bearings and held securely by ARP mains cap studs, which help prevent movement at high revs. Con rods are carefully weighed and matched in sets - again to help internal balancing - and are fitted to 94mm high compression pistons. 4.6 litre engines are built around latest specification short engine assemblies, which feature larger bearing journals, fully counter-balanced cranks, cross bolting of the main bearing caps (preventing movement at high revs) and careful internal balancing of the short engine assembly. 4.8 litre engines are based on the latest factory x-bolted, 4.6 litre large bearing blocks (94mm bore). The stroke is extended to 86mm, using a cross-drilled, billet steel crank. Special 94mm forged psitons are fitted along with new steel conrods, heavy duty bearings and ARP studs ensure a strong and reliable bottom end. 5.2 litre engines are based on the latest factory x-bolted, large bearing blocks. The standard liners are replaced with 'top hat' liners, the bore is increased to 96mm and the stroke is extended to 90mm, using a cross drilled, billet steel crank. Special 96mm forged pistons (with valve cut-outs) are fitted, along with new steel conrods. The cylinder heads are unique to this engine and are fitted with ultra-big valves (1.68" inlet, 1.45" exhaust). Compression ration is 9.35:1. Cylinder heads for 3.9, 4.6 & 4.8 litre Performance engines are the same: we use late-type heads, which are reworked to improve the engine's ability to "breathe". Modifications include gas-flowing the heads, equalising the combustion chambers and matching the opening of the ports to the inlet and exhaust manifold gaskets. We then recut the valve seats and fit larger valves (41.4mm inlet, 35.5mm exhaust), special valve springs and shortened valve guides (with the latest type stem seals), along with new rocker shafts. Finally, we use composite gaskets to eliminate head gasket problems. Compression ratio is 9.35:1. Camshafts are specially selected to get the most from our Performance engines whilst being tractable enough for inner city driving. 4x4 engines have high-torque camshafts which suit both manual and automatic gearboxes equally well. However, we will happily fit any hydraulic camshaft of your choice to one of our Performance engines by special arrangement. Camshaft followers are the High-rev hydraulic type and cam timing is set and maintained with pre-stretched, duplex chains and adjustable vernier steel gear sets. We also fit a new distributor drive gear. Oil pump covers are refaced, modified to prevent the relief valve sticking and fitted with a new relief valve and spring. Timing Cover and sump are fully reconditioned and fitted. To gain maximum benefit from our Performance engines, we recommend that the fuel system, exhaust and air filter be uprated to suit. A full range of uprated fuel system components, tubular exhaust manifolds and K&N air filters are available for most Rover V8 applications. If you are unable to find the part you need, please contact our sales department.

V8 Short Engines

---

Recon Short Engine units are sold on an exchange basis. The old unit must be a suitable type (not Rover P5, P6, MGB V8 & early Range Rover ie with 12mm spark plug reach) otherwise a surcharge will apply. New Short Engines are normally outright - refer to us for latest information.

3.5 litre;
New short engine -
Comprises new block, crankshaft, bearings, pistons, con rods. Less camshaft & followers.
8.13:1 CR - (1) - ETC7714
9.35:1 CR - (1) - RB7121
Recon short engine -
Comprises recon block, rebored with new pistons & new cam bearings, reground crank & new bearings. Less camshaft & followers.
8.13:1 CR - (1) - ETC7714R
9.35:1 CR - (1) - RB7121R

3.9 litre;
New short engine - (1) - RB7487
Comprises new block, crankshaft, bearings, pistons, con rods. Less camshaft & followers.
Recon short engine - (1) - RB7487R
Comprises recon block, rebored, relinered & fitted with new pistons & rings, new cam bearings/reground crank & new bearings. Less camshaft & followers.
Recon short engine (uprated) - (1) - RB7487UR
Comprises new, large journal block, cross-bolted & ARP main studs. Crank/rods & pocketed pistons. Lightened & balanced assembly. Less camshaft & followers.

4.2 litre New short engine;
Comprises new block, crankshaft, bearings, pistons, con rods. Less camshaft & followers.
8.94:1 CR - (1) - ERR4171
Later integral oil pump type.

4.0 litre New short engine;
Series 2 Range Rover aplication only.
Note: Unsuitable for use with pre '95 heads (results in low CR).
Comprises new cross-bolted block, new crankshaft, bearings, pistons & conrods. Less camshaft & followers.
8.13:1 CR - (1) - STC1890
9.35:1 CR - (1) - STC1891

4.6 litre New short engine;
Series 2 Range Rover aplication only.
Note: Unsuitable for use with pre '95 heads (results in low CR).
Comprises new cross-bolted block, new 82mm stroke crankshaft, bearings, pistons & con rods. Less camshaft & followers.
8.13:1 CR - (1) - STC1892
9.35:1 CR - (1) - STC1893

4.6 litre New short engine (high compression);
Pre-series 2 Range Rover applicarion. Suitable for pre '95.
Comprises new cross-bolted block, new 82mm psitons, conrods. Less camshaft & followers.
Note: STC1893 spacer also required when fitting distributor driven oil pump type front timing cover. Sump pan may require relieving to allow swing clearance for front web of crank.
9.35:1 CR - (1) - STC1893HC

4.8 litre New short engine;
Comprises new cross-bolted, 4.6 litre large bearing block (94mm), long stroke (86mm) billet steel crank, forged pistons, steel conrods, heavy duty bearings, ARP studs. Less camshaft & followers.
Note: STC1893 spacer also required when fitting distributor driven oil pump type front timing cover. Sump pan may require relieving to allow swing clearance for front web of crank.
9.5:1 CR - (1) - RB7676
When fitted with pre '95 heads with 36cc combustion chambers.

New Factory 'Turn-Key' Engines

---

We are pleased to be able to offer brand new, Factory supplied V8 turn key engines.
Turn-key engines are available in two capacities: 4.0 & 4.6 litre. As the name suggests, these engines are supplied ready to fit, including ancillaries and injection system.
Both engines are based on the latest factory specification, the 4.6 benefiting from a cross-bolted block and crank-driven oil pump. The 4.0 litre engine comes fitted with a Lucas constant energy distributor ignition system, Lucas Hotwire fuel injection and single serpentine belt ancillary drive.
The 4.6 engine comes fitted with a Lucas GEMS engine management and fuel injection system and single serpentine belt ancillary drive. Ancillaries include: alternator, starter motor, water pump, power steering pump and all pulleys. Engine mounting brackets are also fitted. Turn-key engines are supplied outright, with no exchange surcharge.

New 'Turn-Key' engine;
4.0 litre - (1) - ERR5012BA
4.6 litre - (1) - ERR5013BA

Engine Rebuild Kits

---

Rebuild kit;
3.5 litre - (1) - RB2028 3-5
3.9 litre - (1) - RB2028 3-9

These kits include everything you are likely to need. We assume you'll have the block rebored (in the case of the 3.9, re-sleeved using the liners supplied) and any other machining work done as required. The kits are based on the Range Rover engine. Please note that your crankshaft is required in exchange. For export customers, the crank can be removed from the kit and a price adjustment made, allowing you to have the re-grinding done locally.

Kit contents :- Crankshaft (reground), Bearing shells to suit, Piston set including rings and pins, Piston liner set (3.9 litre only), Oil filter, Sump gasket set inc oil seals, Timing chain, Crank Sprocket, Cam Sprocket, Camshaft and 16 followers, 16 Valves, 16 Valve guides, Valve stem oil seals (inlet), 16 Valve springs, 2 Rocker shafts, 16 Rocker arms, Head gasket set, Core plug set.

Cylinder Block & Components

---

Cylinder block bare;
3.5 litre - (1) - ERC6934
3.9 & 4.2 litre - (1) - ERR7350
4.0 & 4.6 litre - (1) - ERR7349
New Range Rover type.

Cylinder liner set (3.9 litre) - (1) - RB7486
Set of 8 liners for converting 3.5 engine to 3.9 litre bore. Also suitable for replacing the liners in an existing 3.9 litre engine.
Liner & piston set (3.9 litre) - (1) - RB2029
As above, but kit includes standard size 9.35:1 compression pistons and rings for 3.9 conversions.

Stroker kit;
Kits for increasing the cubic capacity of the engine by increasing the stroke to 86mm. Fitted to a 3.5 litre engine (20 thou rebore required), will achieve a capacity of 4.3 litres; fitted to a 3.9 engine will achieve 4.8 litres. Kits contain new crankshaft, con rods, pistons/rings and bearings.
4.3 litre kit - (1) - RB7678
4.8 litre kit - (1) - RB7677

Head gasket set;
3.5 litre models (1970 - 1992)
Tin head gaskets - (1) - GUG1066HS
Composite head gaskets* - (1) - GUG1066HSCOM
3.9/4.2 litre models (1992 - 1994)
Tin head gaskets - (1) - RB7447
Composite head gaskets - (1) - RB7447COM

4.0/4.6 litre New Range Rover - (1) - RRV-233

Head gasket only;
3.5 litre models
Tin gasket - (2) - GEG340
Composite gasket* - (2) - GEG340COM
3.9 & 4.2 litre models (1990 - 1994)
3 rows of cylinder head bolts.
Tin gasket - (2) - RB7448
Composite gasket* - (2) - RB7448COM
3.9, 4.2 & 4.6 litre models (1995 on)
2 rows of cylinder head bolts.
Tin gasket - (2) - ETC7819
Composite gasket* - (2) - ERR7217
* Composite head gaskets are thicker than standard tin gaskets and will therefore lower the engine's compression ratio.
Ideal for correcting compression ratio when heads/block faces have been skimmed.
Approximate gasket thicknesses are as follows:-
Standard (tin) gaskets 0.5mm
Composite gaskets 1.2mm

Sump gasket set;
Includes seals.
All models to 1991 (VIN HA) - (1) - GUG1538CS
All models 1992 (VIN JA) on - (1) - STC1639

Sump gasket only - (1) - AJM539
All models.
Seal (Rear main bearing cap) - (2) - 611089
Cruciform seal.

Crankshaft oil seal (rear);
Early (Rope type) - (1) - 613855
Very early engines only.
All other models - (1) - ERR2640

Timing cover oil seal (front);
Early type - (1) - 602178
For engine nos. 355 & 359, suffix A.
All other models - (1) - ERR6490
Screw-on retainer type.

Core plug set - (1) - RB7105
All models.

Cam bearing set;
All models except 4.0 & 4.6 - (1) - RTC5918
4.0 & 4.6 models - (1) - STC1961

Dowel (bellhousing flange) - (2) - 602141
Drain tap - block) - (2) - 602915
Drain plug - (2) - 129077
Alternative to tap.
Core plug - (2) - 612898
Lower bellhousing flange.
Bolt (main bearing cap) - (10) - 602130
All models.
Stud kit (main bearing cap) - (1) - RB7456
Used instead of standard main bearing bolts, studs provide superior clamping for main bearing caps, preventing them from working loose. Recommended for Performance Engines (not 4.0 or 4.6 New Range Rover).
Cross-bolt (main bearing cap) - (9) - FB110137
4.0 & 4.6 models.
Hex screw (main bearing cap) - (1) - SS110555
4.0 & 4.6 models.
Oil seal (for FB110137) - (9) - ERR3330
Oil seal (for SS110555) - (1) - ERR3331
Stud (front of block) - (1) - 252513
Except 4.0 & 4.6 models.
Plug (Front of block) - (4) - 602147
Breather pipe (Crankcase) - (1) - 603143
Early models.
Core plug (Rear of block) - (1) - 154545
Later models - replaces breather.
Core plug (Side & rear of block) - (8) - 602152
Core plug (camshaft rear) - (1) - 602146

Threaded plug;
All engines except 4.0 & 4.6 - (2) - 602212
4.0 & 4.6 engines - (2) - ERR4314

Crank sensor housing - (1) - ERR3693
4.0 & 4.6 models.

Sump Pan/Oil Pick-Up & Dipstick

---

Sump pan;
All Classic models - (1) - ERR4633
New Range Rover - (1) - ERR5220

Sump gasket set;
Includes seals.
All models to 1991 (VIN HA) - (1) - GUG1538CS
All models 1992 (VIN JA) on - (1) - STC1639

Sump gasket only - (1) - AJM539
All models.
Sump bolt/washer - (16) - SH505051

Drain plug (Sump);
All Classic models - (1) - 603659
New Range Rover - (1) - UAM2957

Washer (Sump drain plug);
All Classic models - (1) - 213961
New Range Rover - (1) - UAM2857

Oil pick-up strainer;
All Classic models - (1) - ERR3677
New Range Rover - (1) - ERR4795

Oil screen - (1) - 602070A
Gasket (Pick-up strainer) - (1) - 90602068A
All models except New Range Rover.
'O' ring (Pick-up strainer) - (1) - ERR4795
New Range Rover.
Spacer (Pick-up strainer) - (1) - ERR4793
New Range Rover.

Setscrew (Strainer to block);
All Classic models - (2) - 253407
New Range Rover - (2) - FS106167

Spring washer (setscrew) - (2) - GHF331
Except New Range Rover.
Nut (Strainer) - (2) - NH605041
New Range Rover.

Dipstick;
All models 1970 - 1985 - (1) - 603173
1986 up to New Range Rover - (1) - ERR1922
New Range Rover - (1) - ERR4905

Dipstick tube;
All models 1970 - 1985 - (1) - ERC2571
1986 up to New Range Rover - (1) - ERR4556
New Range Rover - (1) - ERR4550

'O' ring (Dipstick tube) - (1) - 602545
Except New Range Rover.

Crankshaft

---

Crankshaft;
3.5 & 3.9 litre
3.9 litre up to the following engine nos only: 35D08966B, 36D25523B, 38D27330B.
New (Less shells) - (1) - 612989A
Reground (Including shells - (1) - 612989R
3.9 litre
Above engine nos. onwards - (1) - ERR4060
4.2 litre
Up to engine no. 40D09581B - (1) - ERR3037
Engine no. 40D09582B on - (1) - ERR4152

Stroker kit;
Kits for increasing the cubic capacity of the engine by increasing the stroke to 86mm. Fitted to a 3.5 litre engine (20 thou rebore required), will achieve a capacity of 4.3 litres; fitted to a 3.9 engine will achieve 4.8 litres. Kits contain new crankshaft, con rods, pistons/rings and bearings.
4.3 litre kit - (1) - RB7678
4.8 litre kit - (1) - RB7677
New Range Rover
4.0 - (1) - ERR5090
4.6 - (1) - ERR5091

Main bearing set;
All models except New Range Rover
Standard size - (1) - RTC1718
Oversize +0.010" - (1) - RTC1718-010
Oversize +0.020" - (1) - RTC1718-020
Oversize +0.030" - (1) - RTC1718-030
Oversize +0.040" - (1) - RTC1718-040
Oversize +0.060" - (1) - RTC1718-060
New Range Rover
Standard size - (1) - STC1425
4.0 & 4.6 litre.
NOTE: The latest bearing sets feature thrust plates only on the upper half of centre bearing.

Main bearing set (Heavy duty);
All models except New Range Rover
Standard size - (1) - RB7452
Oversize +0.010 - (1) - RB7452-010
Oversize +0.020 - (1) - RB7452-020

Bolt (Main bearing cap) - (10) - 602130A
All models.
Stud kit (Main bearing cap) - (1) - RB7456
Used instead of standard main bearing bolts, studs provide superior clamping for main bearing caps, preventing them from working loose. Recommended for Performance Engines (not 4.0 or 4.6 New Range Rover).
Cross bolt (Main bearing cap) - (9) - FB110137
4.0 & 4.6 models.
Hex screw (Main bearing cap) - (1) - SS110555
4.0 & 4.6 models.

Oil seal;
For FB110137 - (9) - ERR3330
For SS110555 - (1) - ERR3331

Crankshaft oil seal (Rear);
Rope type (very early vehicles) - (1) - 613855
Lip type - (1) - ERR2640

Timing cover oil seal (Front);
Early type - (1) - 602178
For engine nos.355 &359, suffix A.
All other models - (1) - ERR6490
Screw-on retainer type.

Spigot bush (Crankshaft) - (1) - 549911
All models.

Woodruff key;
All 3.5, 3.9, 4.2 up to 1992 - (1) - 90602025A
3.9 & 4.2 1992 onwards - (1) - ERR2846
Also 4.0 & 4.6.

Crankshaft sprocket (All models) - (1) - 90602372A

Bolt (Crankshaft pulley);
Starting dog type - (1) - 610178
Standard bolt - (1) - ERC417A

Washer (Crankshaft pulley);
Starting dog type - (1) - 602411
Standard bolt type - (1) - ERC416A

Crankshaft Pulley

---

Non air con
Non P.A.S. models to 1985 - (1) - 611019
P.A.S. models to 1985 - (1) - ETC4330 & ETC4369
       Order 1 of each.
Air con models
P.A.S. & non P.A.S. to 1985 - (1) - ETC4330 & ETC4354
       Order 1 of each.
1986 on (Carb & EFi) - (1) - ETC5679
Up to 1992 (VIN JA).
1993 models
Up to engine nos. 35D08967B, 36D25524B, 37D01932B, 38D27331B & 40D09582B - (1) - ERR2799
Above engine nos. onwards - (1) - ERR4866
Up to New Range Rover.
New Range Rover (4.0 & 4.6) - (1) - ERR7372

Vibration damper (3.5 & 3.9);
All models to 1992 - (1) - ERC5462
1992 models
Up to engine nos. 35D08967B, 36D25524B, 37D01932B & 38D27331B - (1) - ETC7339
Above engine nos. onwards - (1) - ERR3442

Vibration damper (4.2) - (1) - ERR4594
Engine no. 40D09582B onwards.
Pulley (Power steering belt) - (1) - ETC4330
All P.A.S. models except New Range Rover.

Balancing rim;
All models to 1991 - (1) - 603301
models from 1992 onwards - (1) - ETC7996

Mud deflector - (1) - 613671
Reinforcing plate - (1) - 602587
All models except 4.0 & 4.6.

Bolt (Crankshaft pulley assembly;
Non P.A.S. models - (6) - GHF104
P.A.S. & air con models - (6) - BH605141

Nut (For above bolt) - (6) - NH605041
All models.

Flywheel & Driveplate

---

Flywheel (Manual);
All Classic models - (1) - ERR5575
New Range Rover - (1) - ERR5396

Ring gear - (1) - 611323A
All manual models.
Bolt (Flywheel to crankshaft) - (6) - SH607081
All models.

Driveplate (Automatic);
3 speed - (1) - FRC5005
Less ring gear.
4 speed (Complete assembly)
1986 to New Range Rover - (1) - FRC7851
New Range Rover - (1) - ERR5658

Bolt (Driveplate to crankshaft);
All except New Range Rover - (6) - SS607061
New Range Rover - (6) - SS607120

Ring gear (Automatic);
All Classic models - (1) - 603340
New Range Rover - Not Supplied Separately

Bolt (Ring gear to driveplate) - (10) - FTC4388
All models.
Washer - (10) - 610736
All models.

Spacer (Driveplate to crankshaft);
Automatics.
3 speed - (1) - FRC5003
4 speed up to New Range Rover - (1) - FTC651

Spigot aligner (Auto);
3 speed - (1) - FRC5006
4 speed to New Range Rover - (1) - FRC7075
New Range Rover - (1) - FTC4606

Bolt (Spigot aligner);
3 speed - (4) - SH110251
4 speed - (4) - BH110111
New Range Rover
4.0 up to engine no. 593A - (4) - FS110141M
4.0 engine no. 594A onwards - (4) - FS110251L
4.6 up to engine no. 450A - (4) - FS110141M
4.6 engine no. 451A onwards - (4) - FS110251L

Washer (Spigot aligner bolt) - (4) - WL110001
All auto models except New Range Rover.
Converter drive plate (Auto) - (1) - FRC7081
1986 to New Range Rover.

Buttress ring (Auto);
4 speed up to New Range Rover - (1) - FRC7080
New Range Rover - (1) - FTC1117

Selective shim (Torque converter height);
1986 to New Range Rover
1.25mm - (ar) - FRC9203
1.45mm - (ar) - FRC9205
1.65mm - (ar) - FRC9207
1.85mm - (ar) - FRC9209
2.05mm - (ar) - FRC9211
New Range Rover
1.20/1.25mm - (ar) - FTC1680
1.30/1.35mm - (ar) - FTC1681
1.40/1.45mm - (ar) - FTC1682
1.50/1.55mm - (ar) - FTC1683
1.60/1.65mm - (ar) - FTC1684
1.70/1.75mm - (ar) - FTC1685
1.80/1.85mm - (ar) - FTC1686
1.90/1.95mm - (ar) - FTC1687
2.00/2.05mm - (ar) - FTC1688
2.10/2.15mm - (ar) - FTC1689

Pistons

---

Piston set;
Includes 8 pistons complete with rings & gudgeon pins.

3.5 litre -
8.13:1 CR
Standard size - (1) - RB7104
Oversize +0.020" - (1) - RB7104-020
Oversize +0.040" - (1) - RB7104-040
9.35:1 CR
Standard size - (1) - RB7246
Oversize +0.020" - (1) - RB7246-020
Oversize +0.040" - (1) - RB7246-040
9.75:1 CR
Standard size - (1) - RB7342
Oversize +0.020" - (1) - RB7342-020
Oversize +0.040" - (1) - RB7342-040
10.5:1 CR
Standard size - (1) - RB7309
Oversize +0.020" - (1) - RB7309-020
Oversize +0.040" - (1) - RB7309-040

3.9 litre -
Standard size
8.13:1 CR - (1) - RB7485KLC
9.35:1 CR - (1) - RB7485KHC

Cylinder liner set (3.9 litre) - (1) - RB7486
Set of 8 liners for converting 3.5 engines to 3.9 litre bore. Also suitable for replacing the liners in an existing 3.9 litre engine.
Piston & liner set (3.9 litre) - (1) - RB2029
As above, but kit includes standard size 9.35:1 compression pistons & rings for 3.9 conversions.

Stroker kit;
Kits for increasing the cubic capacity of the engine by increasing the stroke to 86mm. Fitted to a 3.5 litre engine (20 thou rebore required), will achieve a capacity of 4.3 litres; fitted to a 3.9 engine will achieve 4.8 litres. Kits contain new crankshaft, con rods, pistons/rings and bearings.
4.3 litre kit - (1) - RB7678
4.8 litre kit - (1) - RB7677

Single piston;
Supplied with rings & gudgeon pin.
4.2 litre (8.94:1 CR) - (8) - STC1191S
4.0 litre New Range Rover -
Offset gudgeon type, standard size only.
8.13:1 CR - (8) - ERR5555
9.35:1 CR - (8) - ERR5553
4.6 litre New Range Rover -
Offset gudgeon type, standard size only.
8.13:1 CR - (8) - ERR5556
9.35:1 CR - (8) - ERR5554

Piston Rings

---

Piston rings;
Supplied as engine set.
3.5 litre -
8.13:1, 8.25:1, 9.35:1, 9.75:1 CR
Standard size - (1) - RB7358
Oversize +0.020" - (1) - RB7358-020
Oversize +0.040" - (1) - RB7358-040
10.5:1 CR
Standard size - (1) - RB7421
Oversize +0.020" - (1) - RB7421-020
Oversize +0.040" - (1) - RB7421-040
3.9 & 4.2 litre -
High & low compression ratio.
Standard size - (1) - RB7538
Oversize +0.020" - (1) - RB7538-020P
4.0 & 4.6 litre -
High & low compression ratio.
Standard size - (8) - STC1427

Con rod

---

Con rod assembly;
3.5, 3.9 & 4.2 -
New (Single) - (8) - 602082
Reconditioned (Single) - (8) - 602082R
Engine set (New) - (1) - 602082K
4.0 litre -
New (Single) - (8) - ERR4837
4.6 litre -
New (Single) - (8) - ERR5145

Bolt (Con rod);
3.5,3.9 & 4.2 - (16) - 602609
4.0 & 4.6 - (16) - ERR1772

Nut (Con rod) - (16) - 602061A
Not New Range Rover.
Big end bolt/nut - (1) - RB7500
Engine set of high performance ARP forged chrome moly' steel bolts & nuts. Not suitable for New Range Rover.

Bearing set (Big end);
All engines except New Range Rover.
Standard size - (1) - RTC2117
Oversize +0.010" - (1) - RTC2117-010
Oversize +0.020" - (1) - RTC2117-020
Oversize +0.030" - (1) - RTC2117-030
Oversize +0.040" - (1) - RTC2117-040
Oversize +0.060" - (1) - RTC2117-060

Bearing set (Big end) - (1) - ERR1773
4.0 & 4.6 New Range Rover. Standard size.

Heavy duty bearing set (Big end);
All engines except New Range Rover.
Standard size - (1) - RB7451
Oversize +0.010" - (1) - RB7451-010
Oversize +0.020" - (1) - RB7451-020
Oversize +0.030" - (1) - RB7451-030

Oil Pump & Filter

---

Oil pump cover (body);
Note: From VIN MA650326 (1994), a front cover, which incorporates an integral oil pump, is fitted to all models.
Early models - (1) - 602485
Engine nos. 341, 355 & 359.
All other models - (1) - BHM1554
To VIN MA650326 (1994).

Oil pump cover/remote take-off - (1) - RO1105
Very low profile oil pump cover & relief valve housing for maximum clearance. Use with remote oil filter mounting kit.
Remote oil filter mounting kit - (1) - RB7116
Allows mounting of oil filter away from engine. Kit includes filter housing, hoses & mountings.
Not suitable for New Range Rover.

Bolt (Pump mounting);
7/8" - (3) - 602910
1 1/4" - (2) - 602912
1 9/16" - (1) - 602913

Oil pump repair kit - (1) - RTC2044
All models with separate oil pump. Includes pressure relief valve & spring.
Uprated pressure relief valve spring - (1) - RB7457
For separate oil pump models. Increases oil pressure by approx 10 psi.

Oil pump shaft & drive gear;
Early models - (1) - 602018
Engine nos. 341, 355 & 359.
All other models - (1) - ERC1351A
To VIN MA650326 (1995).

Idler gear (Oil pump);
Early models - (1) - 602017
Engine nos. 341, 355 & 359.
All other models - (1) - 614037
To VIN MA650326 (1995).

Uprating kit (Oil pump) - (1) - RB7480
Early models only (engine nos: 341,355 & 359). Kit includes spacer plate and longer gears to uprate early pumps to later specification. Increases pressure and volume.
Gasket (Oil pump) - (1) - 90602072A
To VIN MA650326 (1994).
Blanking plug - (1) - 151203
Pressure switch outlet.
Washer - (1) - 243967
For blanking plug.
Oil pressure switch - (1) - STC4104
All models.
Washer - (1) - 243967
For pressure switch.

Oil pressure transmitter (early vehicles);
Engine nos. 341, 355 & 359 - (1) - 555947
Other vehicles (where fitted) - (1) - DRC2479A

Washer - (1) - 243967
Pressure transmitter.

Oil pressure transmitter;
For 120° gauge - (1) - 560794
For 140° gauge - (1) - 623050
For 'C - MAX' gauge - (1) - PRC2236

Adaptor (Oil temperature transmitter);
Vehicles up to 1982 - (1) - 611514
Vehicles from 1982 onwards - (1) - 273166

Oil pressure gauge kit - (1) - RX1351
Aftermarket capillary type. Includes gauge & fittings.
Bracket (Oil pressure gauge) - (1) - RB7050

Oil filter;
Early models - (1) - RTC3186
Engine nos. 341, 355 & 359.
All other models - (1) - ERR3340
Including New Range Rover.

Oil Cooler (Engine)

---

If high oil temperatures are a problem, for example when towing, the V8 engine will benefit from the fitting of an oil cooler. We recommend fitting a thermostat at the same time.
Note: An oil cooler was incorporated into the coolant radiator with the introduction of the 3.9 litre engine.
The New Range Rover has a separate oil cooler.
Oil cooler kit - (1) - RRV-089
All models up to 1990.
Thermostat (Oil cooler) - (1) - RS1456

Oil cooler take-off (3.9 engine);
Up to VIN JA624755 (1992) - (1) - ERC8501
From VIN KA624756 (1993) - (1) - ERR2490

Adaptor (Oil filter) - (1) - ERC2226
'O' ring - (1) - ERR852

Oil cooler hose;
Early 3.9 engine up to 1991 (VIN HA) -
Engine to cooler
To VIN FA - (1) - NTC6289
VIN GA onwards - (1) - NTC5972
Cooler to engine
To VIN FA - (1) - NTC5620
VIN GA onwards - (1) - ESR137
3.9 & 4.2 - 1992 (VIN JA) onwards -
Engine to cooler
To VIN JA624755 - (1) - ESR356
VIN KA (1993) to VIN LA (1994) - (1) - ESR1672
VIN MA (1995) onwards - (1) - ESR3693
Cooler to engine
To VIN JA624755 - (1) - ESR355
VIN KA (1993) to VIN LA (1994) - (1) - ESR1671
VIN MA (1995) onwards - (1) - PBP101160

Adaptor (Hose to radiator);
All models.
To VIN JA (1992) - (2) - NTC3858
From VIN KA (1993) - (2) - ESR1262

Adaptor (Pump take-off to hose);
All models.
To VIN JA (1992) - (2) - ETC9064
From VIN KA (1993) - (2) - ESR1239

Sealing ring (Adaptor);
To VIN LA (1994) - (2) - ETC9065
VIN MA (1995) onwards - (4) - ESR1594L

Oil cooler;
New Range Rover.
4.0 litre - (1) - ESR3204
4.6 litre - (1) - ESR3205

Oil cooler hoses;
New Range Rover.
Engine to cooler - (1) - ESR4415
Cooler to engine - (1) - ESR2697

Sealing ring (Cooler hoses) - (4) - ESR2237

Rocker Covers

---

Rocker cover (Single);
Early models (rounded) -
RH - (1) - RTC2350
LH - (1) - ETC8604
1986 onwards -
Rounded
RH - (1) - ETC8681
LH - (1) - ETC8682
Flat top
RH - (1) - ETC8680
LH - (1) - ETC8679
1992 onwards -
RH - (1) - ERR7363
LH - (1) - ERR7360
New Range Rover -
RH - (1) - ERR7367
LH - (1) - ERR7365

Rocker covers (Pair);
Unpainted (Flat top) - (1) - RB7431
Powder coated (Flat top) -
Black - (1) - RB7431RPCBLACK
Red - (1) - RB7431RPCRED

Gasket (Rocker cover);
Standard - (2) - GEG436
Uprated (rubber) - (2) - GEG436UPRATED
All models.

Screw (Rocker cover retaining);
All models except New Range Rover
Long - (4) - 603127
Short - (4) - 602530
New Range Rover
Long - (4) - ERR7371
Short - (4) - ERR4818

Spring washer (Rocker screws) - (8) - GHF331
Not New Range Rover.
Flat washer (Rocker screws) - (8) - GHF300
Not New Range Rover.
Rocker cover 'T' bolts (Chrome) - (2) - RB7440
American style rocker cover hold down bolts. Supplied in sets of 4 (2 required).

Breather/flame trap;
Right hand rocker cover (where fitted).
Original - (1) - RB7432
Short type - EFi original size - (1) - RB7432LOW
Powder coated -
Black - (1) - RB7432PC BLACK
Red - (1) - RB7432PC RED
Chromed - (1) - RB7432C

Breather grommet (pair) - (1) - RB7432ZGROMMET
'O' ring seal (Flame trap) - (1) - 564258

Oil filler neck;
Threaded type - (1) - ERC2989
Screw-on type - (1) - ERC1208
New Range Rover - (1) - ERR7335

Gasket (Filler neck);
Screw-on type - (1) - 612819
New Range Rover - (1) - 564258

Oil filler cap;
Orange type - (1) - 625038A
Pressed steel type - (1) - 598231
New Range Rover - (1) - ERR5218

Seal (Filler cap);
Orange type - (1) - 564258A
New Range Rover - (1) - ERR5219

Breather filter (EFi models) - (1) - ERC3209A
Rear of LH rocker cover.
Cap (Breather filter) - (1) - ERC3208
Plug lead retainer - (2) - 603672
Holds 4 leads.

Cylinder Heads

---

There have been various changes made to the V8's cylinder heads since the introduction of the Range Rover. Consequently, there are numerous different cylinder head part numbers, not all of which are still available. However, as the V8 block has remained essentially unchanged throughout, it is possible (and sometimes beneficial) to fit later cylinder heads in place of earlier ones. The most important difference to bear in mind, when considering replacing cylinder heads, is that some are designed for use with air rails (see Introduction of Engine section) whilst others are not. In this section, we have listed a range of cylinder heads to suit every application - air rail, non air-rail, carburettor & efi. We have also included our range of performance heads, which can be used on all engines. However, they are not designed for use with air rails. All heads are suitable for unleaded fuel.

Cylinder head assembly (Recon);
Complete with new valves, valve guides, springs & valve stem oil seals. Less rocker gear. Cylinder heads are sold individually and are suitable for unleaded fuel.
Carb models -
Non air-rail type - (2) - RB7095R
Air-rail type - (2) - RRV-090R
EFi models - (2) - RB7462R

Cylinder head - new (bare);
1970 to Oct 1985 -
Non air-rail type - (2) - ERC215A
Air-rail type - (2) - ERC676
1986 to 1992 -
Carb models
Air-rail type - (2) - ETC6471
Non air-rail type - (2) - ERC215A
EFi models - (2) - ETC8622
3.5 & 3.9 litre.
1992 onwards -
3.9 litre
Up to eng nos. 35D06576A, 36D14149A, 37D00751A & 38D23045A - (2) - ERR1404
From above eng nos. onwards - (2) - LDF108090
4.2 litre
All models - (2) - LDF108090
New Range Rover
4.0 & 4.6 - (2) - LDF108090

Performance Cylinder Heads

---

Our Performance cylinder heads are carefully modified to gain the maximum power from your engine, whether used on their own or with other modifications, such as a higher lift camshaft or our sports exhaust systems. We use late-type cylinder heads (19mm spark plug reach), cleaned and fully reconditioned. We then gas-flow the heads and enlarge the ports to match inlet & exhaust manifold apertures. Combustion chambers are measured and equalised and the heads are then refaced to achieve a compression ratio of 9.35:1 with composite cylinder head gaskets. We narrow the valve seats, recut them for optimum flow and fit larger valves (41.4mm inlet & 35.5mm exhaust). Shortened & shaped valve guides are fitted, along with the latest-type stem seals, inlet & exhaust. Finally, we fit high performance valve springs. Good results will be obtained by fitting Performance heads to any engine, from a standard 3.5 litre to a Performance 5.2, but to enjoy the maximum benefit offered by their improved efficiency, we recommend fitting a performance cam, tubular exhaust manifolds (see Tubular Manifolds section), K&N air filters or a 4-barrel carburettor, such as the Edelbrock Performer or Holley (see Fuel section). Alternatively, if your vehicle is fuel injected, we recommend a remapped ECU (see Fuel section).
Performance Cylinder Heads are supplied in pairs (less rocker gear) and are suitable for unleaded fuel. They are not designed for use with air rails.
NOTE: Exchange units: Our head assemblies are the later type with 19mm plug reach (as opposed to 12mm) and therefore exchange units must also be of the same type, otherwise a surcharge will apply.

Performance cylinder heads - (1) - RB7467R
Supplied as pair.
NOTE: Use composite head gaskets.

Head Gaskets

---

Head gasket set;
3.5 litre models (1970 - 1992)
with Tin head gaskets - (1) - GUG1066HS
with Composite head gaskets - (1) - GUG1066HSCOM
3.9/4.2 litre models (1992 - 1994)
with Tin head gaskets - (1) - RB7447
with Composite head gaskets * - (1) - RB7447COM
4.0/4.6 litre New Range Rover
with Composite head gaskets - (1) - RRV-233

Head gasket only;
3.5 litre models
Tin gasket - (2) - GEG340
Composite gasket* - (2) - GEG340COM
3.9 & 4.2 litre models (1990 - 1994)
3 rows of cylinder head bolts.
Tin gasket - (2) - RB7448
Composite gasket* - (2) - RB7448COM
3.9, 4.2 & 4.6 litre models (1995 on)
2 rows of cylinder head bolts.
Tin gasket - (2) - ETC7819
Composite gasket* - (2) - ERR7217

Composite head gaskets are thicker than standard tin gaskets and will therefore lower the engine's compression ratio. Ideal for correcting compression ratio when heads/block faces have been skimmed.
Approximate gasket thicknesses are as follows:
Standard (tin) gaskets 0.5mm
Composite gaskets 1.2mm

Cylinder Head Bolts

---

Bolt;
All models except late 3.9, 4.2 & New Range Rover.
Long (7/16" UNC x 3.9") - (6) - 602193A
Medium (7/16" UNC x 2.7") - (13) - 602192A
Tapped bolt (7/16" x 2.7") - (1) - 602450
Early models - for dipstick retainer.
Double-ended bolt (7/16" x 2.7") - (1) - 602200
Later models.
Short (7/16" x 2 1/4") - (8) - 602191A
Late 3.9, 4.2 & New Range Rover
These bolts can be identified by their flanged head. They do not need a separate washer and can be used on earlier engines. However, they are not re-useable and must be replaced once removed.
Long (96mm) - (6) - ERR2944
Medium (66mm) - (14) - ERR2943
NOTE: The outer row of short bolts or 'Outrigger' bolts, has not been used since the introduction of the New Range Rover.

Washer (Cylinder head bolts) - (28) - 602098A
Cylinder head ARP stud kit - (1) - RB7680

Valves, Guides & Springs

---

Various different valves have been used since the Range Rover's introduction; most having the standard "Rover SD1" head diameter: inlet - 40mm, exhaust - 34mm. However, early models were fitted with the Rover P5/P6 type valves, which had a smaller head diameter. In order to benefit from the larger valve size, it would be more practical to fit a pair of later cylinder heads than to attempt to fit the larger valves to early heads.
Efi specification valves are standard SD1 head-diameter, with waisted stems just behind the valve head.
The largest valves that can be fitted to the existing valve seats (later heads only), without the need for extensive machining, are our Big Valves (Inlet - 41.4 mm, exhaust - 35.5 mm, with waisted stems). These valves are particularly suited to large capacity engines.
Finally, the latest factory valves, as fitted to 3.9 & 4.2 engines since 1993, as well as the New Range Rover (4.0 & 4.6 engines), feature the same head diameter as SD1-type valves.
Note: all parts supplied are suitable for unleaded applications.

Inlet valve;
Early engines - (8) - 602166
Eng nos. 355 & 359, suffix A, B, C, D, E.
All other carb engines - (8) - 614088
EFi engines - 3.5, 3.9 & 4.2 litre
Up to eng nos. 35D06576A, 36D14149A, 37D00751A & 38D23045A - (8) - ERC9088
From above eng nos. onwards - (8) - ERR1780
New Range Rover - (8) - ERR1780
Big valve (41.4mm head diameter) - (8) - RB7460

Exhaust valve;
Early engines - (8) - 602165
Eng nos. 355 & 359, suffix A, B, C, D, E.
All other carb engines - (8) - 614089
EFi engines
3.5 litre - (8) - ERC9089
3.9 & 4.2 litre - (8) - ERR7338
New Range Rover - (8) - ERR7338
Big valve (35.5mm head diameter) - (8) - RB7461

Valve seat insert (Inlet);
Early engines
Eng nos. 355 & 359, suffix A, B, C, D, E.
Standard size - (8) - 602052
Oversize +0.010" - (8) - 602223
All other models
Including New Range Rover.
Standard size - (8) - ERC224A
Oversize +0.010" - (8) - ERC225A

Valve seat insert (Exhaust);
Early engines
Eng nos. 355 & 359, suffix A, B, C, D, E.
Standard size only - (8) - 614639
All other 3.5 litre engines
Standard - (8) - ERC210A
Oversize +0.010" - (8) - ERC211A
3.69, 4.2 & New Range Rover
Standard size - (8) - ETC8596A
Oversize +0.010" - (8) - ERC211A

Valve guide (Standard);
For use with standard cam.
Up to 1994 - (16) - 603554
Plain-topped, oil seals on inlet only.
Late 3.9, 4.2, 4.0 & 4.6 (1994 on) - (16) - ERR3648
For use only with matching valves. Machined top , for neoprene seals.

Valve guide (Performance);
Shortened & bulleted, for use with performance cam.
Inlet - (8) - RB7463
Exhaust - (8) - RB7464

Valve stem oil seal;
1970 to 1993 - (8) - ERC7865A
Inlet only.
1993 onwards - (16) - ERR1782
Inlet & exhaust. Not suitable for earlier models.

Valve spring (Standard);
Double (Early engines, Eng nos. 341, 355 & 359, suffix A, B, C, D, E.)
Inner - (16) - 602241A
Outer - (16) - 602240A

Single - (16) - UKC8137

Valve spring (Uprated);
Engine set.
Single - (1) - RB7454
Suitable for all engines with mild road camshaft. Uses standard retaining caps (ERC573).
Double * - (1) - RB7455
Suitable for all engines with performance camshaft. Special retaining caps required (ERC573S).

NOTE: * Machining may be required to valve guide boss when fitting double valve springs to engines previously fitted with singles.

Retaining cap (Valve springs);
Early engines - (16) - 90602451
Fitted with double valve springs.
Single valve springs - (16) - ERC573A
Uprated double valve springs - (16) - ERC573S

Split cotter - (32) - ERC1637A
All models.

Rocker Gear

---

Rocker shaft assembly - (2) - 611660
Assembled ready to fit.
Rocker build kit - (2) - 611660KIT
Includes parts ready for assembly.
Rocker shaft only - (2) - 606661P
Pedestal (Rocker shaft) - (8) - 603734A
Pedestal shims - (1) - 603734SHIMS
Includes three sets of shims of different thickness. Use to set "lifter preload" when fitting a new cam with higher lift than standard.

Rocker arm;
Right hand - (8) - 602153
Original (Alloy).
Left hand - (8) - 602154
Original (Alloy).

Spacer spring (Rocker shaft) - (6) - 602142A
End spring (Rocker shaft) - (4) - 602148A
Wavy washer.
End washer (Rocker shaft) - (4) - 602186A
Split pin (Rocker shaft) - (4) - PC34

Push rod;
Standard - (16) - 603378
Heavy duty - (16) - 603378HD
Larger diameter shaft. Cylinder head guide holes may need enlarging accordingly.
Adjustable set - (1) - 603378ADJ

What is Lifter Preload? "Lifter Preload" refers to the position of the pushrod seat in the lifter (cam follower) when the engine has been assembled and the lifter is positioned on the heel of the cam. Lifter preload must be checked whenever a non-standard component which alters the distance between the rocker arm and the lifter - such as a high lift camshaft or performance cylinder head - has been fitted. Incorrect lifter preload will cause poor running, premature wear or, at worst, engine failure. Check the lifter preload as follows :- With the lifters empty of oil, assemble the rocker shaft & pushrod components, making sure there is no wear in the rocker shafts, rocker arms & pushrods. Checking each lifter in turn, positioned on the heel of the cam, measure the gap between the pushrod seat and the bottom of the circlip groove. There must be a clearance of 0.020" minimum and 0.060" maximum at this position. If the clearance is greater than 0.060", use pedestal shims to decrease. Remember to use equal thickness shims under each pedestal of a shaft to avoid distortion or breakage.

Camshaft & Kits

---

We supply a full range of standard camshafts. In addition, we offer uprated camshafts in 2 different profiles: Mild Road and Fast Road.
Standard cams usually offer a good compromise between power, torque and economy.
Mild Road will give a small increase in power and torque without loss of fuel economy. Fast Road gives greater power at higher revs with a slight loss of low-rev torque, though less so with larger capacity engines. Economy remains good.
Although considered to be the first step towards "uprating" the engine, changing the camshaft alone may not achieve the desired results. We recommend, in fact, that you consider the camshaft as one element of an engine upgrade, which might also include, for example, uprated cylinder heads and a sports exhaust. Consequently, having decided what attributes your engine will need - good low-end torque for towing or a smooth idle for automatic transmission - you can then select the appropriate components to suit from these pages. Remember to fit new followers (lifters) with a new cam.
Finally, all camshafts are interchangeable, with the exception of the New Range Rover versions: due to a change of design, these cams will not easily fit earlier engines.

Camshaft (Standard);
1970 to 1986 -
Low compression engines - (1) - ERC2003A
Compression ratios 8.13:1, 8.25:1, 8.5:1.
High compression engines - (1) - ETC6849
Compression ratio 9.35:1
1986 onwards -
Carb engines
Low compression - (1) - ERC2003A
High compression - (1) - ETC6849
EFi engines
3.5 litre - (1) - ETC6099
3.9 litre - (1) - ERR5924
4.2 litre - (1) - ERR5924
New Range Rover -
4.0 litre - (1) - ERR3720
4.6 litre - (1) - ERR4946

Camshaft (Performance);
Mild road - (1) - RB7444
Straight swap for standard cam. No machining required. Use also Anti pump-up followers ERC4949HD and single springs RB7454.
Fast road - (1) - RB7445
Machining required to valve guides & spring platforms. If fitting without our modified heads, purchase cam kit RB7442, which includes double valve springs & heavy duty followers.

Cam follower (Hydraulic);
All models.
Standard -
Each - (16) - ERC4949A
Set of 16 - (1) - ERC4949AKIT
Heavy duty -
Designed to resist 'pumping-up'.
Each - (16) - ERC4949HD
Set of 16 - (1) - ERC4949HDKIT

Camshaft kit (Standard);
Suitable for all engines except New Range Rover.
Kit 1 - (1) - RB7125
Includes ERC2003A cam & 16 standard followers.
Kit 2 - (1) - RB7489
Includes ERC2003A cam, 16 standard followers, timing chain, timing cover gasket & oil seal, 2 rocker cover gaskets, inlet manifold gasket & 2 inlet manifold seals.

Camshaft kit (Performance);
Suitable for all models except New Range Rover.
Kits include camshaft, anti pump-up followers, uprated valve springs, spring retaining caps, timing disc, cam lube & installation instructions.
Kit 1 - Mild Road - (1) - RB7441
Power band: 1000 - 4500 rpm.
Valve lift: Inlet 11.20mm Exhaust 11.20mm
Timing: Inlet 23/59 Exhaust 59/23.
Kit 2 - Fast Road - (1) - RB7442
Power band: 1500 - 5000 rpm.
Valve lift: Inlet 11.91mm Exhaust 12.44mm
Timing: Inlet 31/73 Exhaust 78/40.

Installation kit (Camshaft) - (1) - RB7488
Includes standard timing chain, timing cover gasket & oil seal, inlet manifold gasket & seals and 2 rocker cover gaskets. All models except New Range Rover.

Gasket (Inlet manifold);
All models.
Tin - (1) - ERC3990
Composite - (1) - ERR7306

End seal (Manifold gasket);
For Tin gasket - (2) - AJM645
For Composite gasket - (2) - ERR7283

Clamp (End seal) - (2) - 602076
Screw (Seal clamp) - (2) - 602236

Performance Camshaft Components

---

Anti pump-up followers - (16) - ERC4949HD
Cam lube - (1) - RX1358
Essential when installing a new cam & followers.
Timing disc (Protractor) - (1) - RX1359
Pedestal shims - (1) - 603734SHIMS
Includes three sets of shims of different thickness. Use to set 'lifter preload' when fitting cams with higher lift than standard.
Cam bearing set (for block) - (1) - RTC5918

Woodruff key (Camshaft);
Early engines - (1) - 90602025
Engine nos. 341, 355 & 359, suffix B, C, D, E.
All other engines - (1) - ERC2838

Timing chain

---

Timing chain;
All models.
Standard - (1) - ERC7929A
Adjustable (kit) - (1) - RB7449
Includes vernier camshaft sprocket, crank sprocket and double roller chain. Also includes timing protractor and Allen key. Allows extremely accurate cam timing whilst eliminating wear common in original parts.

Chain only (Double roller) - (1) - RB7450

Camshaft sprocket (Standard chain);
All models to New Range Rover
Standard (Nylon teeth) - (1) - 610289A
Uprated (Steel teeth) - (1) - 610289VERN
New Range Rover
Standard - (1) - ERR5086

Crankshaft sprocket - (1) - 90602372A
All models.

Spacer (Camshaft);
Mechanical fuel pump type - (1) - 602149
All other vehicles - (1) - ERC2839A
Not New Range Rover.

Distributor drive gear (Camshaft);
Early engines - (1) - 602159
Engine nos. 341, 355 & 359, suffix B, C, D, E.
All other engines - (1) - 614188A
Not New Range Rover.

Washer (Camshaft) - (1) - ERC6552
All engines except New Range Rover.

Bolt (Camshaft);
All engines except New Range Rover.
7/16" UNF x 1 1/8" -
Standard - (1) - 602227A
Uprated - (1) - 602227UR
M12 x 30mm - (1) - ERC5749
Alternative.

Flanged bolt (Camshaft) - (1) - FS110301L
M10 x 30mm. Not New Range Rover.
Screw (Thrust plate) - (2) - SH505061

Woodruff key (Camshaft);
Early engines - (1) - 90602025A
Engine nos. 341, 355 & 359, suffix B, C, D, E.
All other engines - (1) - ERC2838

Timing Cover & Fittings

---

The timing cover fitted to early vehicles incorporates an oil pump gear-housing designed for the early, "short" oil pump gears. Later timing covers have a larger gear-housing, accommodating the longer pump gears, used until the introduction of the crank-driven oil pump. Although the two types of timing cover are interchangeable, the oil pump gears and distributor would also need to be changed. If, however, uprating the early oil pump is your goal, purchase Oil Pump Kit RB7480, which contains a spacer plate and longer gears, along with the correct distributor drive, and fit to the early timing cover. (RB7480 is not suitable for later timing covers).
The timing cover fitted to the New Range Rover is of an updated design, unsuitable for earlier models due to the fact that there is no provision for a distributor. There is, however, an "intermediate" timing cover, fitted to late 3.9 and 4.2 models immediately prior to the introduction of the New Range Rover, which includes a combination of features from both types, such as the crank-driven oil pump and conventional distributor.
Although this timing cover will fit earlier models, the oil pump drive requires a "long-nose" crank, not fitted to earlier engines.

Timing cover;
Short-gear oil pump engines - (1) - 613260
Engine nos. 341, 355, 359 & 398, suffix A, B, C, D, E.
Long-gear oil pump engines - (1) - ETC7385
Engine nos. 341, 355, 398, suffix F and all other engines up to 1995.
3.9 & 4.2 litre (1995 onwards) - (1) - ERR3434
Engine nos. 35D08928B, 36D25155B, 37D02090B, 38D27238B & 40D09582B onwards.
Intermediate engines - (1) - ERR6814
Crank-driven oil pump, from VIN MA650326 (1995).
New Range Rover - (1) - ERR6438

Gasket (Timing cover);
All engines up to 1995 - (1) - 603775A
3.9 & 4.2 litre (1995 onwards) - (1) - ERR7280
Engine nos. 35D08928B, 36D25155B, 37D2090B, 38D27238B & 40D09582B onwards.
New Range Rover - (1) - ERR7280

Timing cover oil seal (Front);
Early type - (1) - 602178
Engine nos. 355 & 359, suffix A.
All other models - (1) - ERR6490
Screw-on retainer type.

Retainer (Oil seal) - (1) - 247766
Screw (Retainer) - (8) - 78782
Timing pointer - (1) - ETC7345
All models.
Screw (Timing pointer) - (2) - HU755
Washer - (2) - WM600041

Bolt (Timing cover to block);
Up to 1992
5/16" UNC x 3" - (1) - BH505241
Lower bolt - (1) - 602388
5/16" UNC x 1 1/8" - (1) - SH505091
1992 onwards (Flanged)
Timing cover bolt - (5) - FB505251S
Timing cover bolt - (1) - FB505311S
Timing cover bolt - (3) - FB505381S
New Range Rover (Flanged)
Timing cover bolt - (5) - FB505171S
Timing cover bolt - (4) - FB505241S

Nut (Timing cover retaining) - (1) - NH605041
All models except New Range Rover.
Dowel (Water pump locating) - (2) - 602201
All models except New Range Rover.
Blanking plate (Fuel pump) - (1) - 610030
Early models fitted with electric fuel pump.
Gasket (Blanking plate) - (1) - 602180
Oil pressure switch - (1) - STC4104
New Range Rover - fitted to timing cover.